Skip to content

TCI support

This page lists what a TCI program can do through RimuDAX, and what it cannot. Use it to find out whether a feature of your program will work before you set it up. To connect a program, see Using TCI.

This page applies to RimuDAX 1.1.20, on Linux and Windows.

Status Meaning
Yes Supported.
Partial Supported, with a limit given in the notes.
No Not supported. RimuDAX ignores the command.

The TCI commands column is for program authors and for comparison with a program's documentation. You do not need it to use RimuDAX.

At a glance

Area Status
Receive audio Yes
Receivers and ports Yes
IQ for skimmers Partial, up to 192 kHz
Frequency and mode Yes
Transmit Partial, split needs a TX slice
CW Partial, no terminal mode or network key
Spots Yes
Meters Yes
Contest recorder No
Receiver DSP and speaker audio No, use RimuSDR

Receive audio

Feature Status Notes TCI commands
Slice receive audio Yes The audio of the slice on the DAX channel for your port. audio_start, audio_stop
Sample rate Yes 8, 12, 24 or 48 kHz, as the program asks. audio_samplerate
Sample format Yes 16-bit, 24-bit or 32-bit integer, or 32-bit float. audio_stream_sample_type
Mono or stereo Yes audio_stream_channels
Frame size Yes 100 to 2048 samples. audio_stream_samples

While the radio transmits, the receive audio is silence.

Receivers and ports

Feature Status Notes TCI commands
Several receivers on one connection Yes On port 50001. Receiver 0 is DAX channel 1, receiver 1 is DAX channel 2, and so on. trx_count, rx_enable
One receiver for each port Yes Ports 50002 to 50008 each reach one DAX channel. See Ports.
Several programs at once Yes For example, two copies of WSJT-X on ports 50001 and 50002.
Turn a receiver on or off Partial A receiver is available when a slice has its DAX channel. A program cannot add or remove one. rx_enable

IQ for skimmers

Feature Status Notes TCI commands
Panadapter IQ stream Yes Needs a DAX IQ channel on the panadapter in RimuSDR. iq_start, iq_stop
48, 96 and 192 kHz Yes Where your radio model offers the rate. A program can change the rate only when no other TCI program uses that IQ channel. iq_samplerate
384 kHz No iq_samplerate

Frequency and mode

Feature Status Notes TCI commands
Read and set the slice frequency Yes The program follows the slice, and tuning in the program tunes the slice. vfo (VFO A), if
VFO B Partial Tunes the split TX slice when there is one. Without a split TX slice, RimuDAX keeps the value but tunes nothing. vfo (VFO B)
Panadapter center Partial Read only. A program cannot move the panadapter. dds
Mode Yes USB, LSB, CW, CW reverse, AM, SAM, FM, NFM, DIGU, DIGL and RTTY. FreeDV shows as DIGU, and DFM as FM. modulation, modulations_list
Filter edges Yes rx_filter_band
RIT and XIT Yes On or off, and the offset. rit_enable, rit_offset, xit_enable, xit_offset
Tuning lock Yes lock
Transmit frequency Yes Sent to the program. tx_frequency
Tuning range Yes Sent to the program. vfo_limits, if_limits
VFO lock No Use lock. vfo_lock
DIGL and DIGU offsets No digl_offset, digu_offset

Transmit

Feature Status Notes TCI commands
Transmit with the program's audio Yes RimuDAX moves TX to the program's slice first. trx (with tci)
Transmit with the radio's microphone Yes trx
Tune Yes tune
RF power and tune power Yes drive, tune_drive
May this receiver transmit Yes Sent to the program. tx_enable
Receive-only Yes When the TX button in RimuDAX is off, programs are told that RimuDAX is receive-only. receive_only
Split Partial On only when you have a split TX slice in RimuSDR. RimuDAX does not create slices. split_enable, rx_channel_enable
Footswitch No tx_footswitch

A transmission with the program's audio stops when that audio stops for 2 seconds. See Transmitting for the other ways a transmission stops.

CW

CW from a program goes out through the radio's CW keyer.

Feature Status Notes TCI commands
CW messages and macros Yes cw_macros, cw_msg
Stop CW Yes Stops at once. cw_macros_stop
Callsign correction while sending Partial Works if the correction arrives before the radio sends those characters. cw_msg, callsign_send
Message speed Yes 5 to 100 WPM. cw_macros_speed, cw_macros_speed_up, cw_macros_speed_down
Keyer speed Yes 5 to 100 WPM. cw_keyer_speed
Delay before CW Yes cw_macros_delay
Terminal mode No The transmitter drops when the text ends. cw_terminal
"Message finished" signal No RimuDAX does not tell the program when a message ends. cw_macros_empty
Key the radio over the network No Network delay makes keying timing unreliable. Use a key or keyer on the radio. keyer

Spots

Feature Status Notes TCI commands
Spots from the program Yes Shown on the panadapter in RimuSDR for 30 minutes. At most 200 at once, and at most 10 a second. spot
Delete and clear spots Yes Removes only spots from TCI programs. Spots from RimuSDR's own spot sources stay. spot_delete, spot_clear
Click a spot in RimuSDR Yes The program is told which spot you clicked. clicked_on_spot, rx_clicked_on_spot

Meters

Feature Status Notes TCI commands
Signal level Yes In dBm. rx_channel_sensors, rx_sensors
Transmit meters Yes Microphone level, power, peak power and SWR, while you transmit. tx_sensors
Meter rate Yes Every 30 to 1000 ms, as the program asks. 200 ms if it does not say. rx_sensors_enable, tx_sensors_enable

Contest recorder

Feature Status Notes TCI commands
Line out recording No The DXLog recorder records nothing through RimuDAX yet. line_out_start, line_out_stop and others

Receiver DSP and speaker audio

Set these in RimuSDR. RimuDAX ignores the commands.

Feature Status TCI commands
AGC No agc_mode, agc_gain
Noise blanker, noise reduction, notch filters No rx_nb_enable, rx_nb_param, rx_nr_enable, rx_anf_enable, rx_apf_enable, rx_anc_enable, rx_nf_enable, rx_dse_enable, rx_bin_enable
Squelch No sql_enable, sql_level
Volume, mute and balance No volume, mute, rx_mute, rx_volume, rx_balance
Monitor No mon_enable, mon_volume
ExpertSDR window focus No app_focus, set_in_focus

Connection

These commands start a session. Programs use them without your help.

Feature Status TCI commands
Session start Yes protocol, device, receive_only, channels_count, ready, start, stop

Something is missing

If your program needs a feature marked No, contact support. Tell us which program it is and what the feature does. We add TCI features when a program needs them.