DSP Controls¶
The DSP Controls window shows every noise reduction, notch filter and noise blanker algorithm of a slice in one place. For each algorithm you can turn it on or off, set its level, and change the advanced settings that firmware 4.3 adds, such as delay, window length and adapt mode.
Requirements
The advanced settings need SmartSDR+. Without it, the window shows Advanced needs SmartSDR+ at the top, and the advanced settings and the reset buttons are grayed out.
Open the window¶
- Click DSP on the slice flag.
- Click the button at the bottom right of the DSP tab.
The window opens on that slice. To change to a different slice, use the
drop-down at the top left. Each slice is listed with its letter and frequency,
for example A 14.250.000.
The algorithm list¶
The list on the left groups the algorithms under three headings:
| Heading | Algorithms |
|---|---|
| Noise Reduction | NR, NRL, NRF, NRS, RNN |
| Notch Filters | ANF, ANFL, ANFT |
| Noise Blankers | NB |
An ON tag shows beside each algorithm that is running. The list shows only the algorithms that the slice mode offers. In FM modes, the window shows DSP controls do not apply in this mode.
Click an algorithm to show its page. A click in the list does not turn the algorithm on or off.
The algorithm page¶
The page heading gives the algorithm and its full name, for example NR (Noise Reduction). The On/Off button beside the title turns the algorithm on or off. A description of the algorithm is at the bottom of the page.
| Algorithm | Settings |
|---|---|
| NR (Noise Reduction) | Level, Delay, Window, Adapt Mode, Inverse |
| NRL (Legacy Noise Reduction) | Level, Delay, Taps, Leakage |
| NRF (Noise Reduction with Filter) | Window |
| NRS (Noise Reduction Spectral) | Level |
| RNN (Noise Reduction with NN) | None. The page has only the description. |
| ANF (Automatic Notch Filter) | Level, Delay, Window, Adapt Mode, Inverse |
| ANFL (Legacy Automatic Notch Filter) | Level, Delay, Taps, Leakage |
| ANFT (FFT Automatic Notch Filter) | Tone Min (dB), Tone Diff (dB) |
| NB (Noise Blanker) | Level |
The ranges are:
- Level
- 0 to 100. NRS runs 0 to 50, as in firmware 4.3.
- Delay and Taps
- 1 to 512.
- Leakage
- 0 to 100.
- Window
- 32, 64, 128, 256 or 512 for NR and ANF. 512, 1024, 2048, 4096 or 8192 for NRF.
- Adapt Mode
- Auto, Fast or Slow.
- Inverse
- ONE or N/2.
- Tone Min (dB)
- -150 to -50.
- Tone Diff (dB)
- 1 to 60.
Reset¶
Reset algorithm, at the bottom of the page, returns the parameters of that algorithm to their defaults. It is shown for NR, NRL, NRF, ANF, ANFL and ANFT.
Reset All, at the bottom left, returns the parameters of every algorithm to their defaults for this slice. The on/off states do not change.
DSP level slider on the slice flag¶
The level slider on the DSP tab of the slice flag now also shows the radio's NR, ANF and NRS levels, and NRS runs 0 to 50, as in firmware 4.3. See DSP filter level sliders.
The NRF level slider and its MIDI action are removed, because the radio has no NRF level. A saved MIDI binding to it is dropped when the mapping loads.
Auto AGC-T¶
Firmware 4.3 can set the AGC threshold (AGC-T) automatically, from the noise floor beside the slice.
Requirements
Auto AGC-T needs SmartSDR+ Early Access. Without it, the buttons are grayed out.
To turn on Auto AGC-T, do one of these steps:
- Click the speaker icon on the slice flag, then click Auto beside the AGC-T slider.
- In the RX panel at the side of the window, click A beside the AGC-T slider.
Click the button again to set AGC-T by hand. The button always shows the mode that the radio reports.