Skip to content

AutoDX

The AutoDX panel shows the CW that the radio decodes on a slice, as text on the screen. AutoDX can also work a split pile-up for you. You enter the DX callsign and your exchange. AutoDX calls when it hears the DX station, sends your exchange when the DX station comes back to you, and counts the QSO.

Requirements

  • Radio firmware 4.3 with the CW decoder, such as the FLEX-8000 series and Aurora. The ADX button is shown only on a radio that reports the CW decoder and has a transmitter.
  • Two CW slices on different frequencies, one of them the TX slice.
  • A callsign set on the radio, in Radio Setup › Radio.
  • For AutoDX itself, a SmartSDR+ Early Access license on the radio. The decoder works without AutoDX on.

Open the panel

Click ADX in the status bar. Click it again to close the panel.

Like the DVK and CWX panels, the AutoDX panel docks on either side of the panadapters, or pops out into its own window. The arrow button at the top right of the panel pops it out or docks it again. To move the docked panel, see Panel layout.

Set up the slices

TX slice
The slice that transmits. The panel only shows it. It must be in CW.
RX slice
The CW slice that AutoDX listens on. The list holds your CW slices that are not the TX slice. Choose the slice that is tuned to the DX station.

The two slices must be on different frequencies. AutoDX works split.

When something is missing

A warning icon at the top right of the panel shows when the setup is not complete. Hold the pointer over the icon, or over the AutoDX check box, to see what is missing. AutoDX will not turn on until it is fixed.

Message What to do
This radio does not support AutoDX. AutoDX cannot be used on this radio.
No slice can listen for the DX. AutoDX needs a CW slice other than the transmitter. Add a second slice in CW.
No slice is set to transmit. Designate a TX slice. Make one of your slices the TX slice.
The transmit slice (letter) is not in CW. Set the TX slice to CW.
Both slices are on the same frequency. AutoDX needs split. Tune the slices to different frequencies.
The radio has no callsign. Set one in Radio Setup > Radio. Enter your callsign in Settings › Radio Setup... on the Radio tab.

Work a split pile-up

  1. Set the RX slice to the DX station's frequency, and the TX slice to the frequency where you will call.
  2. In Detect, type the DX station's callsign only. Do not add "UP".
  3. In Exchange, type your exchange, for example TU 5NN.
  4. In Transmit on, choose Call or Up, Call + Up or Up Only.
  5. Set the timing sliders if necessary (see Settings).
  6. Tick the AutoDX check box at the top of the panel.

AutoDX now listens on the RX slice. It calls when it hears the DX station, sends your exchange when the DX station comes back to you, and counts the QSO.

Take back control

Key the paddle, or send from CWX. AutoDX hands control back to you at once.

Turn AutoDX off

Clear the AutoDX check box. Closing the panel, or disconnecting from the radio, also turns AutoDX off. When you choose a different RX slice, AutoDX stops on the slice you left.

Settings

TX delay
The minimum wait before every call, from 0.1 to 2.0 s. The default is 0.5 s. AutoDX also waits for the DX station to stop sending.
Reply delay
How long to listen for the DX station's reply after a call, from 2 to 60 s. The default is 8 s.
Give up after
Stop trying after this long, from 1 to 10 min. The default is 10 min. A session still ends one hour after it is turned on. With Restart on, AutoDX keeps hunting after the give-up time. With Restart off, it stands down.
Call attempts
From 1 to 10. The default is 3.

Status

State
What AutoDX is doing: Off, Monitoring, About to call, Calling, Awaiting reply, Sending exchange or Logging. The state is green while AutoDX listens, and red from About to call until the transmission ends.
DX call, RX RST and RX exch
The DX callsign, the report and the exchange that AutoDX copied.
QSOs
The QSOs that AutoDX has counted. Reset sets this count to zero. The radio's own count does not change.

Decoder

The Decoder area shows the CW decoded on the RX slice, with its speed in WPM, its SNR in dB, and Locked or Not locked. Received text starts with < and is green. Text that AutoDX sends starts with > and is red. Clear clears the text on the screen.

The decoder works when AutoDX is off.